Wingshield Screwshields in stock!

Wingshield Lrg
The ScrewShield is a “wing-format” shield that extends the Arduino pins to sturdy, secure, and dependable screw terminal blocks. (You even get a few bonus terminals for extra GND and power!)
The wing design allows you to extend just one or both sides (“analog” & “digital”) of the Arduino, and still access the jumpers, LEDs, and buttons on the Arduino.
Thanks to its extra-long header pins, the ScrewShield can be stacked above or below other shields.

  • 1 Analog-side PCB
  • 1 Digital-side PCB
  • 2 sets of 6-pin stacky female header pins
  • 2 sets of 8-pin stacky female header pins
  • ETerminal blocks to fill 32 holes on the board

Get’em now in the Adafruit store!


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



5 Comments

  1. The Wingshield Industries sites’ instructions uses putty to hold the parts in to solder. Perhaps this is common knowledge but I had never seen or heard of someone using that before. Seems like that would be a lot easier then trying to use one of your fingers to make sure you have a part perfectly seated while trying to solder it in. Any chance adafruit can carry whatever this putty is?

  2. david, we use our fingers…but you can get putty at your local hardware store for $1 or so!

  3. Ok.. just wasn’t sure if I had to worry about some putties reacting with anything that might be on a board. Even with vice it is a bit tricky holding headers in place so that you are sure they are flat while still trying to solder them in place. But I haven’t soldered too much so it could be lack of experience.

  4. You can also use “painter’s tape” — that blue masking tape with the weak adhesive. Keep in mind you only have to hold the part in place long enough to solder one or two pins. Once those have cooled it will be firmly in place and you can easily do the rest.

  5. Yes, almost any sticky-ish thing (including fingers) will work. I used poster putty from Target for the docs on the WingShield site.

Sorry, the comment form is closed at this time.