PN532 NFC/RFID Controller Shield for Arduino + Extras. We’ve taken our popular Adafruit PN532 breakout board and turned it into a shield – the perfect tool for any 13.56MHz RFID or NFC application. The Adafruit NFC shield uses the PN532 chip-set (the most popular NFC chip on the market) and is what is embedded in pretty much every phone or device that does NFC. It can pretty much do it all, such as read and write to tags and cards, communicate with phones (say for payment processing), and ‘act’ like a NFC tag. If you want to do any sort of embedded NFC work, this is the chip you’ll want to use!
NFC (Near Field Communications) is a way for two devices very close to each other to communicate. Sort of like a very short range bluetooth that doesn’t require authentication. It is an extension of RFID, so anything you can do with RFID you can do with NFC. You can do more stuff with NFC as well, such as communicate bi-directionally with cell phones
Because it can read and write tags, you can always just use this for RFID-tag projects. We carry a few different tags that work great with this chip. It can also work with any other NFC/RFID Type 1 thru 4 tag (and of course all the other NXP MiFare type tags)
The Adafruit shield was designed by RF engineers using the best test equipment to create a layout and antenna with 10cm (4 inch) range, the maximum range possible using the 13.56MHz technology. You can easily attach the shield behind a plastic plate with standoffs and still read cards through a (non-metal) barrier.
This shield is designed to use I2C or SPI communication protocols. I2C is the default, as it uses fewer pins: analog 4 and 5 are used for I2C (of course you can still connect other I2C devices to the bus). Digital #2 is used for “interrupt” notification. This means you don’t have to sit there and ‘poll’ the chip to ask if a target tag has been found, the pin will pull low when a card, phone, etc is within range. You can adjust which pin is used if you need to keep digital #2 for something else. It is also easy to change the shield over to SPI where you can use any 4 digital pins by shorting two solder jumpers on the top of the PCB. Compatible with any “classic” Arduino – NG, Diecimilla, Duemilanove, UNO – as well as Mega R3 or later. For using the I2C interface with Mega R2 or earlier, two wires must be soldered as the I2C pins are in a different location on earlier Megas.
We are angry, frustrated, and in pain because of the violence and murder of Black people by the police because of racism. We are in the fight AGAINST RACISM. George Floyd was murdered, his life stolen. The Adafruit teams have specific actions we’ve done, are doing, and will do together as a company and culture. We are asking the Adafruit community to get involved and share what you are doing. The Adafruit teams will not settle for a hash tag, a Tweet, or an icon change. We will work on real change, and that requires real action and real work together. That is what we will do each day, each month, each year – we will hold ourselves accountable and publish our collective efforts, partnerships, activism, donations, openly and publicly. Our blog and social media platforms will be utilized in actionable ways. Join us and the anti-racist efforts working to end police brutality, reform the criminal justice system, and dismantle the many other forms of systemic racism at work in this country, read more @ adafruit.com/blacklivesmatter
Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.
Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !
This is a neat shield and a good video to demonstrate it!
Does anyone know about any 134.2KHz RFID readers available for interfacing with the Arduino? The ones I’ve found so far are either MIFARE or 125KHz, but the tags used for pet ID and tracking are all 134KHz as per the ISO 11874. With so many makers owning cats (and dogs), I’d imagine there’d be quite a lot of interesting project ideas out there (including my own ones…).
Just heard back from ID Innovations myself – they have an ISO 11784/11785 compatible 134.2KHz version of their ID-12 in the works!