NEW PRODUCT – Adafruit Pi Box – Enclosure for Raspberry Pi
NEW PRODUCT – Adafruit Pi Box – Enclosure for Raspberry Pi. Keep your Raspberry Pi® computer safe and sound in this lovely clear acrylic enclosure. We designed this case to be beautiful, easy to assemble and perfect for any use (but especially for those who want to tinker!)
The case comes as 6 pieces that snap together, made of crystal-clear acrylic. This ingenious design has no screws or standoffs and there are cute little feet cut into the sides so that it stands up above your desk. There are engraved labels on all the connector slots. You can use all of the connectors on the edges of the Pi: HDMI, Audio, Video, SD slot, micro USB power, Ethernet and the two USB ports. We also added a slot so that you can connect a 26-pin IDC cable to the GPIO breakout pins on the Pi and pass it though the case. For more advanced hacking, the enclosure is designed so that you can remove the top piece and plug any sort of cables you wish into the breakouts in the middle. The case is airy enough that no additional vents or cooling is required – we tested the enclosed Pi over a 24 hour period at full load with no significant increase in temperature.
This product comes with the 6 acrylic pieces. Raspberry Pi computer is not included. No other cables or connectors or accessories are included.
What is the Raspberry Pi® ? A low-cost ARM GNU/Linux box.
The Raspberry Pi® is a single-board computer developed in the UK by the Raspberry Pi Foundation with the intention of stimulating the teaching of basic computer science in schools. The design is based on a Broadcom BCM2835 system on a chip (SoC), which includes an ARM1176JZF-S 700 MHz processor, VideoCore IV GPU, and 256 megabytes of RAM. The design does not include a built-in hard disk or solid-state drive, instead relying on an SD card for booting and long-term storage. The Foundation plans to support Fedora Linux as the initial system software package/distribution, with support for Debian and Arch Linux as well – Wikipedia.
Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards
Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.
Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat and our Discord!
Python for Microcontrollers – Adafruit Daily — Select Python on Microcontrollers Newsletter: PyCon AU 2024 Talks, New Raspberry Pi Gear Available and More! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi
EYE on NPI – Adafruit Daily — EYE on NPI Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey
Brilliant! A nice case is the number one thing I’ve wanted when working with the Pi. The number of connectors on the Pi is great, but it sure does lead to a big mess of cables which inevitably start tugging the Pi around the desk.
Brilliant! A nice case is the number one thing I’ve wanted when working with the Pi. The number of connectors on the Pi is great, but it sure does lead to a big mess of cables which inevitably start tugging the Pi around the desk.
Wow, that things beautiful. Good photography, too.
Beautiful work, love it. now i got to buy it.
We really need a write up on the design of the clips and the design process on how this thing snaps together. Great look and I dig the lack of screws!
Looks really good, any chance you could release the design files?
@jim – they’ll be up here shortly!
http://www.thingiverse.com/adafruit