NEW PRODUCT – Pixel Qi 10″ Dispay with Controller – 1024×600 HDMI/VGA/NTSC/PAL
NEW PRODUCT – Pixel Qi 10″ Dispay with Controller – 1024×600 HDMI/VGA/NTSC/PAL – We’re really excited to offer the revolutionary Pixel Qi display, a full color screen that can also be used in daylight. The Qi has three modes – backlit color, backlit grayscale and daylight grayscale. In normal office/indoor use you’ll want to go with keeping the backlight on to reveal the color layer. The screen works just like any other 10″ TFT with fast refresh (not like slow e-ink). When a bright light shines on it, the display turns ‘gray’ but is still visible. When outdoors in bright light, the backlight can be turned off to revert to a transflective display mode which is much lower power. For much more information please check out the Pixel Qi website.
We’ve packaged up this cool screen with a driver board and power supply. Since the screen is 3.3V LVDS, it’s very hard to connect directly to a microcomputer. The adapter board has a cable that plugs to the screen, there’s a data line and a separate backlight line. (If you want to use the display in low-power backlight-less mode, simply disconnect that plug.) Simply power the controller board with 5-24VDC (we include a 9V power supply) and supply video. You can use HDMI, VGA or NTSC/PAL so you’re covered no matter what interface you want to use! There’s a little keypad thingy you can use to select the input and adjust contrast/brightness/color/etc.
Each order comes with one Pixel Qi screen, LVDS cable, controller board and power adapter. No enclosure, case or stand is included. To demonstrate it, we took some photos with the display connected to a Raspberry Pi, but it will also work connected to any device with HDMI, VGA or NTSC/PAL output. It will not work with a device that only outputs DVI or SECAM. HDMI cable and Raspberry Pi not included!
For use with a Raspberry Pi we suggest editing config.txt to set “hdmi_safe=1” output for best results (otherwise, the Pi may not ‘recognize’ the HDMI display and revert to composite output). Unfortunately Raspbian does not natively support 1024×600 resolution so there will be some black bars around the edge. However, we used it with a Windows computer and it filled the entire screen – just check that your device can use 1024×600.
A 9V US-prong power adapter is included. The power supply may vary from the one shown in the photo, but it will definitely have a US 2-prong plug and will be a switching supply that can be used with 110-240VAC.
Display:
Resolution: 1024 x 600 (color RGB) and 3072×600 (backlight off, grayscale)
Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards
Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.
Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat and our Discord!
Python for Microcontrollers – Adafruit Daily — Python on Microcontrollers Newsletter: New Python Releases, an ESP32+MicroPython IDE and Much More! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi
EYE on NPI – Adafruit Daily — EYE on NPI Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey