NEW PRODUCT – Adafruit USB Power Gauge Mini-Kit

1549_LRG

NEW PRODUCT – Adafruit USB Power Gauge Mini-Kit – This little USB port go-between is like a speed gauge for your USB devices. Instead of hauling out a multimeter and splicing cables, plug this in between for a quick reading on how much current is being drawn from the port. Great for seeing the charge rate of your phone or tablet, checking your battery chargers, or other USB powered projects.

There are a few USB power meters out there, The Practical Meter and the USB Spypow. We wanted something that was made for makers: Reprogrammable micro-controller, analog output, TTL serial output for debugging / datalogging and of course, open source.

Data is passed through transparently from end to end, so you can use it with any USB device at any speed. The power line has a 0.1 ohm current sense resistor an an INA169 high-side current sensor that is tracked by a little ATtiny85 chip. The microcontroller is programmed to read the current draw as well as the bus voltage and light up the strip of LEDs on the side.

1549bottom_LRG

The blue LEDs will light up, one for each Watt of power draw (which is ~200mA at 5V nominal), with a couple levels of PWM dimming for increasing current. You can measure up to 1A of current draw – most USB ports are rated for 500mA.

The green LED is helpful to tell if you have too much droop on your power line. It stays lit as long as the voltage is higher than 4.5V, most devices won’t charge effectively once it goes below that so if the green LED goes out, you know you should check your port, shorten the USB cable, or reduce the current draw.

As an awesome extra, we also print out the voltage, current and wattage data as readable text on the TX pin at 9600 baud. Connect an FTDI friend, USB console cable, microcontroller, XBee, whatever you want that can read 9600 baud TTL serial data for datalogging, plotting or display.

1549kit_LRG

Comes as a mini kit with an assembled & tested PCB plus a separate USB jack and plug as shown above. Before use, solder the jack and plug. It’ll only take you a few minutes and can be done with any soldering iron. Or, advanced users can splice it between a USB extension cable.

Please note: this is a handy gadget but it isn’t a multimeter! We do some basic calibration during test, but the serial output readings are not precise and should be used as a basic guide rather than lab-grade data plots. Assume a variance of at least 0.1V and 50mA due to noise, thermal changes, etc.

In stock and shipping now!


Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat and our Discord!

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 38,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — New Products 11/15/2024 Featuring Adafruit bq25185 USB / DC / Solar Charger with 3.3V Buck Board! (Video)

Python for Microcontrollers – Adafruit Daily — Python on Microcontrollers Newsletter: A New Arduino MicroPython Package Manager, How-Tos and Much More! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

EYE on NPI – Adafruit Daily — EYE on NPI Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

Adafruit IoT Monthly — The 2024 Recap Issue!

Maker Business – Adafruit Daily — Apple to build another chip at TSMC Arizona

Electronics – Adafruit Daily — SMT Tip – Stop moving around!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !


1 Comment

  1. that’s really clever! i often stick usb jacks on projects for charging, but i’m scared to actually use a usb cable to charge it (and not a proper power supply) incase the current spikes and i can’t see it.

    a slightly more fancy version with one of those tiny inexpensive mono OLEDs that are about the same size as this board might add additional handy features (like displaying the real current/voltage, as well as a simple graph). snap it all in an enclosure and you have a beautiful and handy little tool that would be on a lot of folks’ desks!

Sorry, the comment form is closed at this time.