0

NEW PRODUCTS – Adafruit I2C Non-Volatile FRAM Breakout – 256Kbit / 32KByte/ Adafruit SPI Non-Volatile FRAM Breakout – 32Kbit / 8KByte

FRAMbreakout

NEW PRODUCTS – Adafruit I2C Non-Volatile FRAM Breakout – 256Kbit / 32KByte and Adafruit SPI Non-Volatile FRAM Breakout – 32Kbit / 8KByte

NewImage

Adafruit I2C Non-Volatile FRAM Breakout – 256Kbit / 32KByte

FRAM, or Ferroelectric Ram, is the coolest new data storage method that all the fashion magazines are talking about. Oh wait, no that’s quilted handbags. But FRAM is pretty damn cool too! It’s similar to Dynamic random-access memory, only with a ferroelectric layer instead of a dielectric layer. This gives it stable handling (the bytes you write are non-volatile) with dynamic responsiveness (you can write them very fast!)

Now, with our I2C FRAM breakout board you can add some FRAM storage to your next DIY project. FRAM allows for a lower power usage and a faster write performance. It’s excellent for low-power or inconsistent-power datalogging or data buffering where you want to stream data fast while also keeping the data when there’s no power. Unlike Flash or EEPROM there’s no pages to worry about. Each byte can be read/written 10,000,000,000,000 times so you don’t have to worry too much about wear leveling.

This particular FRAM chip has 256 Kbits (32 KBytes) of storage, interfaces using I2C, and can run at up to 1MHz I2C rates. Each byte can be read and written instantaneously (like SRAM) but will keep the memory for 95 years at room temperature.

We picked up the largest chip that has I2C and is also 5V compliant. You can use this chip with either 3V or 5V power and logic. It comes in a breadboard-friendly breakout and a spare stick of 0.1″ male header for soldering on.

We also have an SPI FRAM breakout board – which is smaller in size but faster (20MHz max SPI clock rate)

In stock and shipping now!


NewImage

Adafruit SPI Non-Volatile FRAM Breakout – 32Kbit / 8KByte

FRAM, or Ferroelectric Ram, is the coolest new data storage method that all the fashion magazines are talking about. Oh wait, no that’s quilted handbags. But FRAM is pretty damn cool too! It’s similar to Dynamic random-access memory, only with a ferroelectric layer instead of a dielectric layer. This gives it stable handling (the bytes you write are non-volatile) with dynamic responsiveness (you can write them very fast!)

Now, with our SPI FRAM breakout board you can add some FRAM storage to your next DIY project. FRAM allows for a lower power usage and a faster write performance. It’s excellent for low-power or inconsistent-power datalogging or data buffering where you want to stream data fast while also keeping the data when there’s no power. Unlike Flash or EEPROM there’s no pages to worry about. Each byte can be read/written 10,000,000,000,000 times so you don’t have to worry too much about wear leveling.

This particular FRAM chip has 32 Kbits (8 KBytes) of storage, interfaces using SPI, and can run at up to 20MHz SPI clock rates. Each byte can be read and written instantaneously (like SRAM) but will keep the memory for 95 years at room temperature.

We picked up the largest chip that has SPI and is also 5V compliant. You can use this chip with either 3V or 5V power and logic. It comes in a breadboard-friendly breakout and a spare stick of 0.1″ male header for soldering on.

We also have an I2C FRAM breakout board – which is large in size but slower (1MHz max I2C clock rate)

In stock and shipping now!


Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Join 14,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython 2019!

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Follow Adafruit on Instagram for top secret new products, behinds the scenes and more https://www.instagram.com/adafruit/


Maker Business — Robotics manufacturer Anki is stripped for parts

Wearables — Epoxy and foam, BFFs

Electronics — Lead-free Soldering Temperature

Biohacking — Vitamin-C + Gelatin for Accelerated Recovery

Python for Microcontrollers — See you at Supercon, Python #2 language on GitHub and more! #Python #Adafruit #CircuitPython #PythonHardware @circuitpython @micropython @ThePSF @Adafruit

Adafruit IoT Monthly — Helping Harry's Heart, CircuitPython meets AWS IoT and more!

Microsoft MakeCode — Lenticular Art Display with Crickit

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



1 Comment

  1. Thomas Stewart

    32 Kbit == 8 KByte? Are those the new, "lite" bytes that I keep reading about in all the fashion magazines? Or did you mean 8 KNibbles? 😉

    (apologies if this is posted more than once; submit is leading me to a blank page…)

Sorry, the comment form is closed at this time.