Build your own radio telescope to listen to meteors #backtoschool

Build Your Own Radio Telescope to Listen to Meteors

This project would be a perfect school activity- you can get the lesson plans here. Via Science Friday.

The Perseids are a favorite meteor shower of many Northern Hemisphere skywatchers, especially during the mild summer nights of August. But if you can’t get outside or if you’re clouded out, you can still listen to the meteor shower any time of day using a simple FM radio.

Meteors are caused by small bits of dust and rock from space hitting the Earth’s atmosphere and burning up upon entry, producing a flash of light. Earth gets hit with approximately 40 tons of this stuff a day on average, but that increases during a meteor shower event as the earth goes through a stream of debris left behind by a comet (in the case of the Perseids, it’s Comet Swift-Tuttle).

When that little bit of natural space debris burns up in the atmosphere, it flashes briefly, creating a “shooting star” to marvel at if you have clear, dark skies. It also briefly leaves a trail of charged particles behind. Turns out, those charged particles can reflect radio waves from distant television and radio stations, temporarily boosting their signal from afar. These radio waves are what you can detect with a simple radio receiver.

The best way to do this, as described here, is to get a hold of an FM radio receiver with a good antenna. Your car radio is a great example. Although it is recommended that you modify it a bit or buy a high-end radio, you can try this with a small home radio as well.

Now you have to find a mostly blank spot on your radio dial. You shouldn’t be tuned to a nearby station, but one that you can just barely make out because it is very distant. Then listen closely for a jump in the station’s power—that indicates a meteor has passed overhead! This works best at night when there is less interference from human-made radio signals, and early in the morning hours when the earth is facing into the stream of comet debris. If you just want to tap into the observations from some really large receivers, you can tune into SpaceWeatherRadio’s streaming service.

Meteors aren’t the only things you can observe with bits of equipment you might have at home. With a leftover satellite dish and some parts from your local electronic store, you can build an Itty Bitty Radio Telescope to observe the sun. You can put one together using an RV kit, or check Craigslist and Freecycle for people who are just looking to get rid of old equipment. In the one I recently put together for a kids’ summer camp, I used a satellite finder that emits a sound that gets higher in pitch when it comes across a strong radio source, such as the sun. Don’t get confused by the sounds, however. Radio waves emitted from the sun or any astronomical or human-made objects are light, NOT sound. It’s our electronic equipment that converts the information to sound that we can hear. (You can learn more about “sounds” from space in this SciFri article.)

How you build your Itty Bitty Radio Telescope depends on what equipment you get. I picked up an old Channel Master 1004IF on eBay to detect the signal collected by my dish. That doesn’t have its own power supply, so I followed these instructions for making my own with some wire, coaxial cable, batteries, and a soldering iron. (If you don’t already know how to solder, there are maker and hacker spaces popping up all over the place giving lessons!) Once the system was all connected and powered, I was able to detect my first radio waves from the sun on a cloudy day! Some people mount their Itty Bitty to a tripod, and others build a “Lazy Susan” for it to rotate on. Mine is still “handheld” while I dig up some more parts. In addition to observing the sun, this is a great educational tool to show how just about everything around you gives off a few radio signals, and there are even classroom lessons to help you do just that.

Read more.


August is Back to School Month here at Adafruit! Each day we’ll be bringing you a post for educators on the blog. Stay tuned for product guides, tutorials from the Adafruit Learning System, and inspiration from around the web! Get started by checking out Adafruit’s educational resources, such as our kits and project packs, suggested products for young engineers, and an extensive selection of books to help you learn!

Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here:

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in!

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community!

CircuitPython – The easiest way to program microcontrollers –

Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at !

No Comments

No comments yet.

Sorry, the comment form is closed at this time.