NEW PRODUCTS – Monochrome 2.42″ 128×64 OLED Graphic Display Module Kit / Monochrome 1.54″ 128×64 OLED Graphic Display Module Kit

NEW PRODUCTS – Monochrome 2.42″ 128×64 OLED Graphic Display Module Kit / Monochrome 1.54″ 128×64 OLED Graphic Display Module Kit

NewImage
NewImage

Monochrome 2.42″ 128×64 OLED Graphic Display Module Kit

If you’ve been diggin’ our monochrome OLEDs but need something bigger, this display will delight you! These displays are 2.42″ diagonal, and very readable due to the high contrast of an OLED display. This display is made of 128×64 individual white OLED pixels, each one turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this graphic display for its crispness!

The driver chip, SSD1305 can communicate in three ways: 8-bit, I2C or SPI. Personally we think SPI is the way to go, only 4 or 5 wires are required and its very fast. The OLED itself requires a 3.3V power supply and 3.3V logic levels for communication. We include a breadboard-friendly level shifter that can convert 3V or 5V down to 3V, so it can be used with 5V-logic devices like Arduino.

NewImage
NewImage
NewImage

The power requirements depend a little on how much of the display is lit but on average the display uses about 50mA from the 3.3V supply. Built into the OLED driver is a simple switch-cap charge pump that turns 3.3V into a high voltage drive for the OLEDs.

Each order comes with one assembled OLED module with a nice bezel and 4 mounting holes. The display is 3V logic & power so we include a HC4050 level shifter. We also toss in a 220uF capacitor, as we noticed an Arduino may need a little more capacitance on the 3.3V power supply for this big display! This display does not come with header attached but we do toss in a stick of header you can solder on. Also, the display may come in SPI mode. You can change modes from 8-bit to SPI or I2C with a little soldering, check out the tutorial for how to do so. Please Note: Metro not included! A microcontroller such an Arduino is required to use.

Getting started is easy! We have a detailed tutorial and example code in the form of an Arduino library for text and graphics. You’ll need a microcontroller with more than 512 bytes of RAM since the display must be buffered. The library can print text, bitmaps, pixels, rectangles, circles and lines. It uses 512 bytes of RAM since it needs to buffer the entire display but its very fast! The code is simple to adapt to any other microcontroller.

In stock and shipping now!


NewImage
NewImage

Monochrome 1.54″ 128×64 OLED Graphic Display Module Kit

If you’ve been diggin’ our monochrome OLEDs but need something bigger, this display will delight you! These displays are 1.54″ diagonal, and very readable due to the high contrast of an OLED display. This display is made of 128×64 individual white OLED pixels, each one turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this graphic display for its crispness!

The driver chip, SSD1305 can communicate in three ways: 8-bit, I2C or SPI. Personally we think SPI is the way to go, only 4 or 5 wires are required and its very fast. The OLED itself requires a 3.3V power supply and 3.3V logic levels for communication. We include a breadboard-friendly level shifter that can convert 3V or 5V down to 3V, so it can be used with 5V-logic devices like Arduino.

NewImage
NewImage
NewImage

The power requirements depend a little on how much of the display is lit but on average the display uses about 50mA from the 3.3V supply. Built into the OLED driver is a simple switch-cap charge pump that turns 3.3V into a high voltage drive for the OLEDs.

Each order comes with one assembled OLED module with a nice bezel and 4 mounting holes. The display is 3V logic & power so we include a HC4050 level shifter. We also toss in a 220uF capacitor, as we noticed an Arduino may need a little more capacitance on the 3.3V power supply for this big display! This display does not come with header attached but we do toss in a stick of header you can solder on. Also, the display may come in SPI mode. You can change modes from 8-bit to SPI or I2C with a little soldering, check out the tutorial for how to do so. Please Note: Metro not included! A microcontroller such an Arduino is required to use.

Getting started is easy! We have a detailed tutorial and example code in the form of an Arduino library for text and graphics. You’ll need a microcontroller with more than 512 bytes of RAM since the display must be buffered. The library can print text, bitmaps, pixels, rectangles, circles and lines. It uses 512 bytes of RAM since it needs to buffer the entire display but its very fast! The code is simple to adapt to any other microcontroller.

In stock and shipping now!


8-6-2021 (August 6, 2021) is the Snakiest day of the year and it’s also this year’s CircuitPython Day! The day highlights all things CircuitPython and Python on Hardware. See you there!

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Join 30,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Follow Adafruit on Instagram for top secret new products, behinds the scenes and more https://www.instagram.com/adafruit/

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — Over 500,000 manufacturing jobs are going unfilled

Wearables — Stop the sweat

Electronics — Hummm… 60Hz noise in your amplifier driving you nuts?

Python for Microcontrollers — Python on Microcontrollers Newsletter: EuroPython 2021, CircuitPython 7.0.0 alpha 5 and more! #Python #Adafruit #CircuitPython @micropython @ThePSF

Adafruit IoT Monthly — Forest Fire Beacons, IoT for Beginners, and more!

Microsoft MakeCode — MakeCode for the micro:bit - 2021 Release!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — New Products 7/28/21 w/ Adafruit MCP9601 (MCP96L01) I2C Thermocouple Amplifier – STEMMA QT /Qwiic!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.