Biohacking: Quantifying Exercise Recovery

Last week I ran 135 miles in one non-stop push. Now I’m trying to figure out how long I need give myself to recover from that effort. Combining data from The Oura Ring and a Nokia Body Cardio Scale I can gain some insight as to how my recovery is going. I’ve decided to focus on these four measurements as critical indicators :

  • Heart Rate Variability (HRV)
  • Temperature Deviation (TD)
  • Respiration Rate (RR)
  • Water Mass (WM%)

The first three indicators I can pull from The Oura Ring. Let’s take a look at Heart Rate Variability as this is considered one of the most reliable indicators for recovery. The Oura Ring records HRV all night long and provides an average value. While I normally have an HRV in the 60’s when I finished running on the 16th my HRV had dropped to 40 almost 20 points below normal. You can read more about HRV here. I have seen this behavior consistently with running ultra marathons of varying distance. My HRV value levels are reduced for several days after these events.

 

Another sign that I am in a recovery mode is an increase in body temperature. Normally I am with .1 degree celsius of my normal body temperature. After this event I have been over 1.1 degree C over normal. In other words I am running hot and it would also look this way if I were sick. After the initial night of sleep my temeprature deviation was greatly reduced to being much closer to normal, but not fully recovered being between .2C – .6C above normal.

Respiration rate is simply an average of how many breaths/min are taken during a full nights sleep. I went into this event with 13.5 breaths/min and immediately afterwards was at 15.6 breaths/min. A huge increase that took five days to get back to normal levels.

My hydration level is usually at 61%. I have over a year of data confirming this. However, it has been really bumped up post race peaking out at 66%. I’m using the Nokia Body Cardio scale to collect this data and what is interesting to note is how slowly the recovery time has been to release the excess water in my feet and ankles. Even five days after the event I’m still around 64% water mass which is several percentage points about my norm.

It is starting to look like a week long recovery to get everything back to normal. However, since this was a long, slow, low effort event I’ve already resumed my maintenance mileage of seven miles a day. While some people prefer to go by feel alone I have found the combination of data and feel to be the best indicator of when I can resume more stressful training.


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.