0

NEW PRODUCTS – Adafruit CharliePlex LED Matrix Bonnets – 8×16 LEDs – Green / Blue / Warm White LEDs

4120

NEW PRODUCTS – Adafruit CharliePlex LED Matrix Bonnets – 8×16 LEDs – Green / Blue / Warm White LEDs


You won’t be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16×8 LED display can be placed atop any Raspberry Pi computer with a 2×20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C.

We carry these Bonnets in a few vivid colors – this is the green LED matrix.

3467 iso ORIG 2019 02

What is particularly nice about this Wing is the I2C LED driver chip has the ability to PWM each individual LED in a 16×8 grid so you can have beautiful LED lighting effects, without a lot of pin twiddling. Simply tell the chip which LED on the grid you want lit, and what brightness and it’s all taken care of for you. You get 8-bit (256 level) dimming for each individual LED.

The IS31FL3731 is a nice little chip – and it runs happily over 3.3V power. Inside is enough RAM for 8 separate frames of display memory so you can set up multiple frames of an animation and flip them to be displayed with a single command. Since it uses I2C, it takes up only the SDA/SCL pins on your Pi and can share those pins with other I2C devices and sensors.

Comes fully assembled, no soldering required, so you can plug it in immediately. To program it, you’ll use our CircuitPython library, which works with Linux computers like Raspberry Pi. After a pip install, run some of the examples to display simple graphics or text.

3467 top ORIG 2019 02

3467 quarter ORIG 2019 02

Next up, Blue!


3467

You won’t be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16×8 LED display can be placed atop any Raspberry Pi computer with a 2×20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C.

We carry these Bonnets in a few vivid colors – this is the blue LED matrix.

What is particularly nice about this Wing is the I2C LED driver chip has the ability to PWM each individual LED in a 16×8 grid so you can have beautiful LED lighting effects, without a lot of pin twiddling. Simply tell the chip which LED on the grid you want lit, and what brightness and it’s all taken care of for you. You get 8-bit (256 level) dimming for each individual LED.

The IS31FL3731 is a nice little chip – and it runs happily over 3.3V power. Inside is enough RAM for 8 separate frames of display memory so you can set up multiple frames of an animation and flip them to be displayed with a single command. Since it uses I2C, it takes up only the SDA/SCL pins on your Pi and can share those pins with other I2C devices and sensors.

Comes fully assembled, no soldering required, so you can plug it in immediately. To program it, you’ll use our CircuitPython library, which works with Linux computers like Raspberry Pi. After a pip install, run some of the examples to display simple graphics or text.

And lastly, the Warm White LEDs!


4122

You won’t be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16×8 LED display can be placed atop any Raspberry Pi computer with a 2×20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C.

We carry these Bonnets in a few vivid colors – this is the warm white LED matrix.

4122 iso ORIG 2019 02

What is particularly nice about this Wing is the I2C LED driver chip has the ability to PWM each individual LED in a 16×8 grid so you can have beautiful LED lighting effects, without a lot of pin twiddling. Simply tell the chip which LED on the grid you want lit, and what brightness and it’s all taken care of for you. You get 8-bit (256 level) dimming for each individual LED.

The IS31FL3731 is a nice little chip – and it runs happily over 3.3V power. Inside is enough RAM for 8 separate frames of display memory so you can set up multiple frames of an animation and flip them to be displayed with a single command. Since it uses I2C, it takes up only the SDA/SCL pins on your Pi and can share those pins with other I2C devices and sensors.

Comes fully assembled, no soldering required, so you can plug it in immediately. To program it, you’ll use our CircuitPython library, which works with Linux computers like Raspberry Pi. After a pip install, run some of the examples to display simple graphics or text.

4122 top ORIG 2019 02

4122 quarter ORIG 2019 02

In stock and shipping now!


Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Join 15,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython 2019!

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Follow Adafruit on Instagram for top secret new products, behinds the scenes and more https://www.instagram.com/adafruit/


Maker Business — Patreon: 4 million patrons, $1 billion in payouts

Wearables — Shake it off

Electronics — Switch Mode Power

Biohacking — Vitamin-C + Gelatin for Accelerated Recovery

Python for Microcontrollers — 200 CircuitPython Libraries, Binho, BLE, and more! #Python #Adafruit #CircuitPython #PythonHardware @circuitpython @micropython @ThePSF @Adafruit

Adafruit IoT Monthly — Machine Learning 101, PWNing the ESP32, and more!

Microsoft MakeCode — Deep Breathing Encouragement with Circuit Playground Express!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.