0

New Products 5/2/19 Featuring Adafruit #PyBadge Low Cost! @adafruit #adafruit

Screen Shot 2018 05 04 at 7 44 26 AM

We’ve got the New nEw NEW for you right here:


NEW PRODUCTS THIS WEEK


4170 01

GPIO Ribbon Cable 2×8 IDC Cable – 16 pins 12″ long: Connect this to that! If you want to bridge those contacts out onto another PCB, you’ll want this GPIO Ribbon Cable! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05″ ribbon cable and keyed IDC connectors on both ends. It’s perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or extend the cable a little farther. Read more


4171 02

Dual RCA Jack for Adafruit I2S Audio Bonnet: RCAs are some of our favorite plugs. Easy to use and easy to handle, and still very popular on stereo equipment due to their universal nature. This dual/stereo RCA jack set is the right kind to solder right into our I2S Audio Bonnet for Raspberry Pi – perfect for those who want composite output rather than a 3.5mm stereo jack. Read more


4173 00

Short Male Header Kit for ItsyBitsy: These three Short Male Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you’re in business! Read more


4174 00

Short Female Header Kit for ItsyBitsy: These three Short Female Headers alone are, well, lonely. But pair them with any of our ItsyBitsy boards, and you’re in business! Read more


4191 02

2 x AAA Battery Holder with On/Off Switch & JST PH Connector: This battery holder connects 2 AAA batteries together in series for powering all kinds of projects. We spec’d these out because the box is nicely slim, and 2 AAA’s add up to about 3V for low-voltage electronics projects, plus it has a nifty on-off switch. Read more


4193 01

2 x AA Battery Holder with On/Off Switch & JST PH Connector: This battery holder connects 2 AA batteries together in series for powering all kinds of projects. We spec’d these out because the box is fairly slim, and 2 AA’s add up to about 3V for many low voltage electronics projects, plus it has a nifty on-off switch. Read more


4202 00

Diffused 3mm LED Pack – 5 LEDs each in 5 Colors – 25 Pack: Need some miniature indicators? We are big fans of these diffused LEDs. They are fairly bright, so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Read more


4203 02

Diffused 5mm LED Pack – 5 LEDs each in 5 Colors – 25 Pack: Need some indicators? We are big fans of these diffused LEDs. They are fairly bright, so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Read more


4204 00

Diffused 10mm LED Pack – 5 LEDs each in 5 Colors – 25 Pack: Need some chunky indicators? We are big fans of these diffused LEDs. They are fairly bright, so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Read more


4225 01

NVIDIA Jetbot Parts Pack: The Jetbot Parts Pack is everything you need to get your next vroom vroom project up and rolling! Read more


4226 00

Adafruit INA260 High or Low Side Voltage, Current, Power Sensor: This breakout board may well be the last current sensing solution you every need to buy. Not only can it do the work of two multimeters, but it can do it with amazing precision and flexibility. With it you can measure high or low side DC current, the bus voltage, and have it automatically calculate the power. It can do so over impressive voltage, current, and temperature ranges with better than 1% accuracy, all while delivering the data in an easy to use format over I2C. Read more


3939 00

Adafruit PyBadge LC – MakeCode Arcade, CircuitPython or Arduino – Low Cost Version: What’s the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you’re on a budget? That’s right, it’s the Adafruit PyBadge LC! We wanted to see how much we could cram into a ​3 3⁄8 × ​2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. Read more


New Products 5/2/19 Featuring Adafruit PyBadge Low Cost!

Visit www.adafruit.com/new for more info.


Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, or even use Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for MakeCode, CircuitPython, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Join 12,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython 2019!

Have an amazing project to share? The Electronics Show and Tell with Google Hangouts On-Air is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Follow Adafruit on Instagram for top secret new products, behinds the scenes and more https://www.instagram.com/adafruit/


Maker Business — Trade war rolls on, effects will have lasting implications

Wearables — Block the light

Electronics — Stay disciplined with ERC

Biohacking — Focus Building Meditation with Michael Taft

Python for Microcontrollers — Consumers Should Immediately… Python the Circuit! #Python #Adafruit #CircuitPython #PythonHardware @circuitpython @micropython @ThePSF @Adafruit

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.