New Products 5/22/19 Featuring Adafruit PyGamer! #adafruit

Screen Shot 2018 05 04 at 7 44 26 AM

We’ve got the New nEw NEW for you right here:


NEW PRODUCTS THIS WEEK


4182 02

3.5mm Mono Audio Jack to Alligator Clip Cable

This cable is easy to understand – you get a 3.5mm mono audio jack on one end, and two alligator clips on the other. It’s also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It’s also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection.

Read more


4181 02

3.5mm Mono Audio Plug to Alligator Clips

This cable is easy to understand – you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It’s also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It’s also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection.

Read more


4198 01

USB C to USB C Cable – USB 3.1 Gen 4 with E-Mark – 6″ long

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs!

Read more


4199 01

USB C to USB C Cable – USB 3.1 Gen 4 with E-Mark – 1 meter long

This cable is a little more expensive than most USB cables because it has all the data pins connected, so it can be used for any USB C device, with any power or speed requirements. The internal wires are 32 AWG. It also includes an EMARK chip, required by the USB C specification but sometimes left out. That means you can use this for high current (5A) charging.

Read more


4232 10

Multifunctional USB Digital Tester – USB A and C

This handy (pun intended?) tool can measure voltage, current, power, charge time, and other measurements for USB A, Micro B, and USB C! It features a colorful display that pops up when you plug in a power supply. Each click of the button gives you a different display and readout. A long press will reset the data for when it does Coulomb-counting (total power consumption). We like the simple display that comes up first with big Voltage and Current output, but you have lots of options.

Read more


4249 04

Heat-Set Insert For Soldering Irons – M5 Inserts

Wanna improve the connection strength between your project’s 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong and reusable machine screws and heat-set inserts. Heat set inserts are only a few cents a piece and have a grooved outside, with theads on the inside. Originally they were designed for injection molded parts but they work fabulously for 3D printed plastic as well.

Read more


4239 06

Heat-Set Insert For Soldering Irons – #4-40 / M3 Inserts

Wanna improve the connection strength between your project’s 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong and reusable machine screws and heat-set inserts. Heat set inserts are only a few cents a piece and have a grooved outside, with theads on the inside. Originally they were designed for injection molded parts but they work fabulously for 3D printed plastic as well.

Read more


4208 02

JST SH 4-pin Right Angle Connector (10-pack) – Qwiic Compatible

If you’re a DIY enthusiast who likes to micro-manage your project’s connections, here is a 10-pack of some micro JST SH connectors! They’re solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place.

Read more


4177 03

M5Stack Gray Development Kit – ESP32 Dev Board w/ MPU9250

Get yourself a kit that can do it all! The M5Stack Gray Development Kit is a ESP32-based WiFi microcontroller that’s compatible with MicroPython and Arduino. It comes jam-packed with Wi-Fi / Bluetooth capability, running at 240 MHz with the dual-core processor and 4MB of SPI Flash.

Read more


4178 08

M5Stack Basic Core IoT Development Kit – ESP32 Dev Board

Get yourself a kit that can do it all! The M5Stack Basic Development Kit is a ESP32-based WiFi microcontroller that’s compatible with MicroPython and Arduino. It comes jam-packed with Wi-Fi / Bluetooth capability, running at 240 MHz with the dual-core processor and 4MB of SPI Flash.

Read more


4176 04

M5Stack FACES ESP32 Pocket Computer – Keyboard, Game, Calculator

Get yourself a kit that can do it all! The M5Stack FACES Pocket Computer is a ESP32-based 3-in-1 pack with swappable keyboard / Gaming / calculator panels! Each panel can be upgraded through downloading firmware updates.

Read more


4228 00

Plastic Button Caps For Square Top (10-pack) – 8mm Diameter

These Reese’s Piece’s lookin’ bits fit perfectly on top of tactile buttons with 2.4mm square tops and give a satisfying 8mm diameter surface area for your fingers to press.

Read more


4238 00

Adafruit PyGamer Acrylic Enclosure Kit

You’ve got your PyGamer, and you’re ready to start jammin’ on your favorite arcade games. You gaze adoringly at the charming silkscreen designed by Ada-friend PaintYourDragon. The nostalgia is palpable!

Read more


4242 00

Adafruit PyGamer for MakeCode Arcade, CircuitPython or Arduino

What fits in your pocket, is fully Open Source, and can run CircuitPython, MakeCode Arcade or Arduino games you write yourself? That’s right, it’s the Adafruit PyGamer! We wanted to make an entry-level gaming handheld for DIY gaming, and maybe a little retro-emulation. It’s not the fastest and best of everything but it is an all-in-one dev board with a lot of possibilities!

Read more


New Products 5/22/19 Featuring Adafruit PyGamer

Visit www.adafruit.com/new for more info.


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.