New Products 12/31/2020 featuring Adafruit LTR390 UV Light Sensor – STEMMA QT / Qwiic!

Screen Shot 2018 05 04 at 7 44 26 AM

We’ve got the New nEw NEW for you right here:


NEW PRODUCTS THIS WEEK


4853 03

Translucent Snap-on Case for micro:bit V2

This simple Translucent Snap-on Case is both good looking and tough enough to toss into your bookbag or toolbox. It has slim cut-outs for your cable, speaker, and battery. It’s translucent plastic so you can still easily see the micro:bit PCB markings and LEDs shining through. The bottom section is open so you can plug it into a micro:bit accessory.

Read more


4852 03

Smoke Snap-on Case for micro:bit V2

This simple Smoke Snap-on Case is both good looking and tough enough to toss into your bookbag or toolbox. It has slim cut-outs for your cable, speaker, battery. It’s darkened plastic but you can still easily see the LEDs shining through. The bottom section is open so you can plug it into a micro:bit accessory.

Read more


4855 00

GPIO Female Socket Riser Header – 2×2 4-pin

This 0.1mm pitch 2×2 Female Header is the perfect boost to use with boards that use the 4-pin ‘PoE’ header on the Raspberry Pi 3 and 4, like the Raspberry Pi PoE HAT! It’s a great pairing to the 2×20 socket riser header to get a full lift.

Read more


4860 01

Adafruit Prop-Maker Starter Kit – Make your own Lightsaber!

Use the force and Adafruit Feather to build a battle-grade lightsaber! If you can’t make the hyperspeed jump to Ilum for your Jedi rite of passage, the Adafruit Prop-Maker Starter Kit is perfect for making your very own 3D-printed NeoPixel Lightsaber. It contains practically everything but the khyber crystal!

Read more


4862 00

Adafruit CYBERDECK Bonnet for Raspberry Pi 400

Howdy keyboard cowboys, are you surfing the information superhighway with a Pi 400? Want a cool heads-up display, or maybe you need to wire up some NeoPixel wetware…?

Read more


4863 02

Adafruit CYBERDECK HAT for Raspberry Pi 400

Cyber-warriors, listen up here! We’ve got with some zero-day unreleased hardware we just dumpster-dived. Now you can crack kodes, and write skripts with style, thanks to the CYBERDECK HAT for Raspberry Pi 400 from Adafruit zaibatsu.

Read more


4823 03

40 Pin GPIO Extension Cable for any 2×20 Pin Raspberry Pi – 150mm / 6″ long

That new Raspberry Pi 400 computer you just got has a row of 2×20 pin headers on the right side – those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun lies. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails.

Read more


4831 00

Adafruit LTR390 UV Light Sensor – STEMMA QT / Qwiic

The LTR390 is one of the few low-cost UV sensors available, and it’s a pretty nice one! With both ambient light and UVA sensing with a peak spectral response between 300 and 350nm. You can use it for measuring how much sun you can get before needing to covering up.

Read more


New Products 12/31/2020 featuring Adafruit LTR390 UV Light Sensor – STEMMA QT / Qwiic!

Visit www.adafruit.com/new for more info.


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.