Extremely Mini Raspberry Pi Cyberdeck @Raspberry_Pi #PiDay #RaspberryPi
A proper cyberdeck should look like it was kludged together in an alley in the Sprawl, under a sky the color of a television tuned to a dead channel. It should look like you can close it up, run through a crowd, jump onto a subway, and disappear into the night. It should look like anyone can make it, but only you can use it. Mike Horne’s little Raspberry Pi Cyberdeck checks all those boxes. Here’s more from Raspberry Pi Pod:
A 3S LiPo gives approx 11.1V, which is obviously too much for the Pi which wants 5-5.2V. I grabbed hold of an adjustable buck converter that takes a high power feed and converts it (steps it down) to whatever voltage you need, courtesy of a small adjustment pot at the top. Here it is with the pot turned to approximately what I needed. I later adjusted it to 5.1V to give the Pi some headroom.
You’ll see that the output of the converter goes into an Enviro+ board that is plugged into the Raspberry Pi Zero 2 W. This is where things get a little convenient. I knew I wanted some kind of sensor display for the project, and I happened to have an Enviro+ already. With a little experimentation, I found that I could take the voltage out of the converter and “shove” it into the GND and 5V pins of the Enviro+ and this would power the Pi. Marvellous. There is a cheaper board – the plain Enviro – so you might want to consider that. I also realised that I could add a control button to the Enviro+ by soldering a button to the other GND and #4 (GPIO 4), so I did that as well. The nice thing about the Enviro is that it breaks out “just enough” pins to make it easy to add things on. Those I2C (SDA/SCL) pins are just begging for more sensors – I don’t have any more room in the case, though!
Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!
Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards
Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.
Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7:30pm ET! To join, head over to YouTube and check out the show’s live chat and our Discord!
Python for Microcontrollers – Adafruit Daily — Python on Microcontrollers Newsletter: Open Hardware is In, New CircuitPython and Pi 5 16GB, and much more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi
EYE on NPI – Adafruit Daily — EYE on NPI Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey
Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!