NEW PRODUCT – Adafruit Pixel Trinkey – USB Key for NeoPixel / DotStar Driving

NEW PRODUCT – Adafruit Pixel Trinkey – USB Key for NeoPixel / DotStar Driving

Blast-off to Pixel Planet with the Adafruit Pixel Trinkey, a co-pilot for those who like to shine bright. This little microcontroller board plugs into your computer’s USB port and can drive tons of NeoPixel (SK6812, WS2812, etc) or DotStar (e.g. AP102) LEDs without having to do any soldering or complex wiring. The SAMD21 chip on board has 32KB of SRAM, that means thousands of pixels! All from the convenience of your computer with support for Arduino, CircuitPython or Windows 11’s built-in Dynamic Light Control

NeoPixels and Dotstars are ‘smart’ LEDs that can display 24-bit color, they’re bright, colorful, individually-addressable, and come in dozens of different shapes: from flexible strips, to individual dots, to rings, and beyond. However, you need a microcontroller to drive them: something that can generate the exact pattern of data that they desire to set each pixel color. Normally folks use something like an Arduino, which will work just fine, but sometimes needs level shifting or separate power, or just has gangly wires.

This board contains the microcontroller, plus level shifting in a compact package that pokes out an inch from your computer USB port. On the end is a screw terminal block that can accept stranded or solid-core wires 26 to 18 AWG with four ports: 5V power, Data, Clock and Ground. If you’re using DotStars, wire up the ‘input’ side of your LEDs to the 4 pads. If you’re using NeoPixels, you can have one or two strands, where the second strand uses the Clock pin as the data generator.

Computer USB ports can provide up to 1A which we’ve found will drive about 150 pixels without difficulty as long as they are not all on full white at max brightness. If you need to drive a ton more pixels, simply disconnect the 5V power wire and use an external power source – just make sure that the ground wire from the external power is connected to the ground of the Trinkey+pixels. You can monitor the USB 5V line voltage thanks to a resistor divider on the board.

If you want to add additional circuitry, such as an Infrared remote input, or potentiometer, or a button, there’s a JST-SH 3-pin connector on board. Use a JST SH 3-pin cable to access the 3V, ground and pin D4. There’s also a separate mini NeoPixel for status feedback if desired.


  • ATSAMD21E18 32-bit Cortex M0+ – 48 MHz 32-bit processor with 256KB Flash and 32 KB RAM
  • Native USB supported by every OS – can be used in Arduino or CircuitPython as a USB serial console, MIDI, Keyboard/Mouse HID, and even a little disk drive for storing Python scripts
  • Can be used with Arduino IDE or CircuitPython
  • 0.1″ / 2.54mm Terminal Blocks – Attach LEDs with no soldering! Just use a common screwdriver.
  • On-board RGB NeoPixel LED
  • JST SH 3-pin compatible connector – For extra hardware connectivity
  • Reset switch to start your project code over or enter bootloader mode
  • Open Source Hardware so you have full control over your LEDs

In stock and shipping now!

5953 iso ORIG 2024 05

5953 side 01 ORIG 2024 05

5953 side 02 ORIG 2024 05

5953 side 03 ORIG 2024 05

5953 top ORIG 2024 05

5953 demo mac ORIG 2024 05 copy

5953 demo PC V1 ORIG 2024 05

5953 quarter ORIG 2024 05

Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here:

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in!

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community!

CircuitPython – The easiest way to program microcontrollers –

Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at !

No Comments

No comments yet.

Sorry, the comment form is closed at this time.